Acrosser AR-B5630 Manual do Utilizador

Revision: 2.0 1 AR-B5630 Board Socket P Intel® Core™2 Duo EPIC SBC with Intel® GME965 Express Chipset , DVI/LCD, Dual LAN and PCI-104 Eexpansi

Revision: 2.0 10 2.1.2 Bottom Side

Revision: 2.0 11 2.1.3 List of Connector and Jumper Setting PWR2 External +12V DC power input connector. KM1 Keyboard/Mouse Connnecto

Revision: 2.0 12 2.2 Connector and Jumper Setting Table 1. PWR2: External +12V DC power input connector. 2. CON2: ATX function connector. 3.

Revision: 2.0 13 10. IDE1: PATA connector. 11. J12: Front panel connector. (NOTE 1) PIN SIGNAL PIN SIGNAL 1 RESET 2 GND 3 D7 4 D8 5 D6 6

Revision: 2.0 14 14. USB2: Internal USB2, USB3 connector. 15. USB1: External USB0, USB1 connector. PIN SIGNAL PIN SIGNAL 1 +5V 2 +5

Revision: 2.0 15 18. LCD1: LCD panel (LVDS, 18-bit/36-bit) connector. 19. LCDPW1: LCD panel inverter power connector. E: Ev

Revision: 2.0 16 22. J9: RS422/RS485 signal connector (for COM2). 23. COM3*: RS232 signal connector for port #3. PIN SETTING 1 RS485 DATA+

Revision: 2.0 17 28. GPIO1:8-bit TTL-5V GPIO connector. 29. AUDIO1: 5.1 channels Audio signal connector. PIN SETTING PIN SETTING 1

Revision: 2.0 18 *:1. COM1 is the external UART RS-232 port, the text description on the PCB board is “CON1”. *:2. COM2 is the internal UART R

Revision: 2.0 19 3 BIOS SETTING This chapter describes the BIOS menu displays and explains how to perform common tasks needed to get the system u

Revision: 2.0 2 Revision Version Date Author Description 2.0 2010/06/11 Roger Nan Initial release

Revision: 2.0 20 3.1 Main Setup The <Main Setup> choice allows you to record some basic hardware configuration in your computer system and

Revision: 2.0 21 3.2 Advanced Chipset Setup This section allows you to configure and improve your system and follows you to set up some system fe

Revision: 2.0 22 3.3 Power Setup Use this main to specify your setting for power management. Option Choice Description ACPI Function Enabled

Revision: 2.0 23 3.4 PnP/PCI Setup The option configures the PCI bus system. All PCI bus system on the system use INT#, thus all installed PCI ca

Revision: 2.0 24 3.5 Peripherals Setup This option controls the configuration of the board’s chipset. Control keys for this screen are the same a

Revision: 2.0 25 3.6 PC Health Setup This section shows the parameters in determining the PC Health Status. These parameters include temperatures

Revision: 2.0 26 3.7 Boot Setup This section is used to exit the BIOS main menu. After making your changes, you can either save them or exit the

Revision: 2.0 27 3.8 Exit Setup This section is used to configure exit mode. Option Choice Description Save & Exit Setup Pressing <En

Revision: 2.0 28 Set Password Pressing <Enter> on this item for confirmation: ENTER PASSWORD: When a password has been enabled, you will be

Revision: 2.0 29 3.9 BIOS Update The BIOS program instructions are contained within computer chips called FLASH ROMs that are located on your sys

Revision: 2.0 3 Copyright 2010 All Rights Reserved. Manual’s first edition: June 11, 2010 For the purpose of improving reliability, design and f

Revision: 2.0 30  Watch Dog Timer Reset Sample Code (IT8712F-A/IX-L) The WDT (Watch Dog Timer) is used to generate a variety of output signals

Revision: 2.0 31 // Set Watchdog outportb(IO_Port_Address,0x07); // Point to Logical Device Number Reg. outportb(IO_Port_Address+1,0x07);

Revision: 2.0 32  NOTE 1: J12: Front panel connector. When using AT mode in the system, the pin9-10 of header J12 must be shorte

Revision: 2.0 4 Table of Contents 1 Introduction ... 5 1.

Revision: 2.0 5 1 INTRODUCTION Welcome to the AR-B5630 ECIP AT/ATX Single Board Computer. The AR-B5630 is EPIC board with Socket P Intel Core™2

Revision: 2.0 6 LED 2 LEDs for Power and HDD Power LED (Green), HDD (Orange) refer to AR-B1831 Button Reset button (use pin header) PinHeade

Revision: 2.0 7 1.2 Package Contents In addition to this User's Manual, the AR-B5630 package includes the following items:  AR-B5630 AT/

Revision: 2.0 8 1.3 Block Diagram

Revision: 2.0 9 2 H/W INFORMATION This chapter describes the installation of AR-B5631. At first, it shows the Function diagram and the layout of